Galvanic corrosion and Fasteners

Added 15.02.21

Galvanic corrosion and Fasteners

Added 15.02.21

 

Tackling the Problem of Corrosion

Machines, equipment and structures often have to operate in harsh environments. The sort of conditions that can lead to problems with corrosion. A simple solution is to use stainless steel components. Stainless steel has an oxide layer on the surface that renders it electrochemically passive. In simple terms, it is much less likely to rust than other steels.

To avoid this sort of corrosion many parts are being made from stainless steel. However, this can lead to problems with another sort of corrosion – galvanic corrosion – if you use fasteners not made from stainless steel.

Galvanic corrosion, sometimes called bimetallic corrosion or electrolytic corrosion, occurs when two dissimilar metals are immersed in a conductive solution and are electrically connected. One metal (the cathode) is protected, whilst the other (the anode) is corroded. Salt water is the most common conductive solution that causes these problems.

So anything exposed to sea water and water from roads has to be protected. Even rainwater contains ions that will cause galvanic corrosion.

 

Galvanic Corrosion Disasters

In the 17th century, the Royal Navy noticed that the lead sheathing used on their ships caused the rudder irons and bolt heads to disintegrate. Then, when they used iron nails to attach copper sheathing the nails disintegrated. By 1886 when the Statue of Liberty was built the engineers knew to put a layer of shellac between the outer copper skin and the wrought iron frame and this lasted for nearly 100 years until the shellac was replaced with PTFE in the 1980s.

But in 2011 the lighting fixtures in the Big Dig vehicle tunnel in Boston started to fall out of the ceiling. Improper use of aluminium in contact with stainless steel in the presence of salt water had led to rapid corrosion. Replacing the lights cost around $54 million.

 

Stainless Steel is not always the Answer

We were recently approached by a customer to supply a spring clip to hold three stainless steel pipes. The customer specified a stainless steel clip to ensure there were no problems with galvanic corrosion. But there was a problem.

Carbon steel clips are formed in a soft state and then heat treated (Austempered) to give them the desired “spring”. But producing spring clips from stainless steel is very challenging.

Making parts in a temper rolled stainless steel such as ASTM 301 means that the tooling needs to be made to over-bend the parts. This takes them beyond the natural elastic limit and allows for spring-back. This is OK if the part is large enough to allow for this over bend. But when you try to form a “U” gap in a part to fit on a 1mm panel you cannot bend the part enough to allow for spring-back.

So the JET PRESS team had to find an alternative.

 

Meeting the needs of our customer

The challenge was to make a carbon steel clip that delivered a salt spray rating of 480 hours, even when in contact with stainless steel pipes. We developed a Zinc-Nickel electroplate with a trivalent (CrIII) passivate treatment. Then we added clear sealer called McDermid JS500. The combination of these finishes and treatments met the brief. It resulted in a spring steel fastener that, even when in direct contact with stainless steel pipes, was able to pass a 480 hour salt spray test.

Not only were there no signs of red rust, but the new part cost less than a stainless steel version.

We stock a wide range of stainless steel fasteners and components including Gas SpringsSnap Fasteners, Cable Glands, Linear Tracks, Drawer Slides, Quarter Turn Latches and Leaf Hinges

If you would like to know more about dealing with galvanic corrosion or any other ways we can help you please call our sales team on +44 1623 551 800 email [email protected] or contact us online.

> Back to News and media
For more information contact us +44 1623 551 800 Enquire

A Camloc Gas Strut Makes Light Work of a Heavy Lid

We worked with our customer, deploying a Camloc Gas Strut to create a functional and cost effective solution. The...

Learn More

Fir Tree Buttons save Lives

A team from the Warsaw University of Technology came third in the general classification, third in the technical...

Learn More

Testimonials

""We appreciate your fast replies (to mails & inquiries) and accurate information very much" "

Ervo Projects - Robberechts
Testimonials
Back To Top